Carving intensity constant engine LIC laser intensity compensation module

± 2% power stability, allowing for zero attenuation during long-term engraving

Overcome the problem of temperature drift, adapt to continuous operation in 25-40 ℃ environment, and improve the consistency of dark material carving patterns by 85%

±1. 5℃
Temp Accuracy
50ms
response speed
24 months
Extended lifespan of laser
Appointment for technical demonstration Apply for temperature difference environment testing

Temperature - an invisible killer of carving accuracy

The effect is unstable

For every 10 ℃ increase in laser temperature, the spot power attenuates by 3-5%, and the difference in engraved patterns on dark wooden boards is greater than 15%

15%+
Pattern differences

Equipment shutdown loss

The traditional solution requires a 15 minute shutdown for cooling every 2 hours, and the effective time for 8-hour operation is only 5.5 hours

31%
Time loss

Poor environmental adaptability

In summer, the power fluctuation of the 35 ℃ studio exceeds ± 10%, and manual calibration requires repeated testing 58 times

58 times
Calibration testing
A survey conducted by a cultural and creative studio shows that 25% of the waste rate is due to energy parameter deviations caused by temperature
25%
Waste rate caused by temperature

Dual closed-loop temperature control system - millisecond level collaborative dynamic cooling+power calibration

① Temperature sensing layer

  • High precision temperature sensor: real-time monitoring of laser core component temperature
  • Sampling frequency: 100Hz (industry average 50Hz)
  • response delay

② Dynamic cooling layer

  • TED1-12703 Semiconductor Refrigeration Chip
  • Temperature difference control between hot and cold ends
  • Micro heat pipe heat dissipation: heat dissipation efficiency increased by 40%

③ Power compensation layer

  • Exclusive temperature power model: P=P ₀ × (1-0.003 × (T-25))
  • Step by step current regulation
  • Automatically compensate 0.3% of the driving current for every 1 ℃ increase in temperature

Core technical parameters

25-40℃
Temperature range
±2%
power stability
50ms level
response speed
'3W
Cooling mode power consumption

From downtime loss to doubling production capacity - LIC refactoring carving machine usage scenarios

Case 1: Home DIY Acrylic Carving

pain spot
After continuous carving for 30 minutes, the difference in light transmittance of the pattern exceeds 10%, requiring frequent calibration
Solution
The temperature control compensation system automatically adjusts the current 12 times within 2 hours to maintain stable power
benefit
Carving efficiency increased by 300%, and the scrap rate decreased from 18% to 3%
300%
Efficiency improvement

Case 2: Leather Customization in Cultural and Creative Studio

pain spot
Power fluctuation ± 15% at 35 ℃ environment, with 4 daily shutdowns for heat dissipation
Solution
Micro heat pipe cooling module+dynamic compensation, continuous 8-hour non-stop operation in 40 ℃ environment
benefit
The daily production capacity has increased from 15 pieces to 40 pieces, and the delivery cycle has been shortened by 62.5%
167%
Ramp Up

Case 3: Wooden board teaching in educational institutions

pain spot
Student operation leads to a 25% scrap rate due to temperature drift
Solution
Built in automatic compensation mode, automatically adjusts current by 0.3% for every 1 ℃ temperature rise
benefit
The cost of a single teaching session has been reduced from ¥ 80 to ¥ 30, and the pass rate of student works has increased to 92%
92%
Qualification rate of works

Four dimensional compaction traditional scheme - LIC redefines temperature compensation standard

Dimension Traditional temperature control LIC Double Closed Loop System
Temp Accuracy ± 5 ℃ (only for cooling and heat dissipation) ± 1.5 ℃ (cooling+power dual compensation)
response speed >200ms (passive heat dissipation) 50ms level (active perception+regulation)
Continuous operation 2-hour shutdown for heat dissipation 8-hour continuous operation without attenuation
Cost effectiveness Laser lifespan of 8 months Extend lifespan to 24 months (saving 66% of costs)

Equipped with LIC - giving your engraving machine full temperature range operation capability

Applicable scenarios

Dark wood carving
Temperature sensitive material
Long term mass production
Continuous 8-hour homework
High temperature environment operation
Like a summer workshop

Collaboration mode

Standardized module procurement: plug and play, compatible with 5-60W engraving machines
Customized development: supports special temperature range (such as -10 ℃ low temperature) requirements

Instant Consultation

+86-15623097174
24/7 technical support hotline
Limited time benefits
The top 20 orders will receive a complimentary 'Temperature Power Compensation Debugging Manual

LIC product series

Professional laser intensity compensation solution

No data available at the moment